View source for Phoenix RepRap

=Project Synopsis=
We've been trying to brainstorm a good project idea that we can focus on to present to ASU for the $2000 grant we're aiming for.  One project that would definitely put us on the map and would also allow us to reach out to the local community would be procuring a Rapid-Prototyping device.  The RepRap project is a prime example of one whose initial creator's intention was not only to make a device that was as inexpensive as possible but also one that can replicate itself.  Seeing the cost benefits analysis, as well as, the vast improvements with version II of this device(Mendel) we're thinking about going with that design.

--Update - ASU did not fund us so we did it ourselves.  Take that establishment.

==Design Summary==

Check out the RepRap main site here:<br>
http://reprap.org/bin/view/Main/WebHome

They've got a great video/mini documentary explaining the background of the RepRap concept including an interview with the designer:<br>
http://vimeo.com/5202148

Check out the below link for a good video summary of what the "Mendel" is:<br>
http://objects.reprap.org/wiki/Mendel_Overview

==Construction==

The RepRap team has done a pretty good job of ensuring that the design specs are open source so that the world wide community can participate in building and even bettering what they've started.

Below is their how to section on building a "Mendel" version of the RepRap:<br>
http://objects.reprap.org/wiki/How_to_make_RepRap_Version_II_%22Mendel%22

==Budget==

This is a tally of costs so far, and providers used.  You can see the original estimate on the rep rap site of $520 was rather low.  With all the various shipping charges (plus we got 15lbs of plastic) we will likely almost double this.  They also do not mention the impossibility of finding the prototyped/printed parts for the rep rap.  They are approximately 100 hours to print and thus we've found few rep rap/makerbot owners willing or able to print those parts for us.  These parts can also be rapid prototyped for around $1500 dollars which is slightly more than the advertised $20 dollars.

===Located Parts===
{| border="1" cellpadding="10" cellspacing="0"
|-
|'''Item'''
|'''US cost'''
|'''Notes'''
|-
|Bearings
|$76.14 shipped
|TheBigBearingStore.com
|-
|Fasteners
|109.20
|Mcmaster.com
|-
|Belt
|see Fasteners
|Mcmaster.com
|-
|Extruder parts(machined)	
|$32.40 shipped
|reifsnyderb on rep rap forums
|-
|Motors
|302.85 shipped
|Store.Makerbot.com
|-
|Plastic Stock
|See motors
|Store.Makerbot.com
|-
|PCBs
|See Motors
|Makerbot
|-
|Electronics
|169.16
|Parted out from Digikey, Allied,Arrow,Newark and Mouser
|-
|Thick sheet MDF, between 4mm and 6mm and at least 42cmx40cm
|57.15	
|Lowes
|-
|Bar (smooth rod) BZP NOT BMS A2 Steel even better - at least 3m - M8 (8mm diameter)
|See Thick Sheet
|Lowes
|-
|Studding (threaded rod) -BZP  M8 (8mm diameter) at least 9 meters
|See Thick Sheet
|Lowes
|-
|epoxy,ties
|See Thick Sheet
|Lowes
|-
|silicon grease, kapton tape
|~33.00
|Grainger
|-
|pcb strip board, heatshrink tubing, 
|n/a
|Scrap
|-
|12 PC or laptop Power Supply
|n/a
|Multiple units donated by various members
|-
|5v FTDI
|19.04 shipped
|Sparkfun
|-
|Extruder parts - 6-ohm length of fibreglass-insulated nichrome wire,
|.50cents a foot
|http://store.makerbot.com/nichrome-wire-31-ga.html
|-
|Extruder thermistor
|4.06
|http://www.circuitspecialists.com/prod.itml/icOid/6136
|-
|2pin .1inch pitch connectors to replace rj45s
|~10
|Newark.com EC100F-2 CE100F22-2
|-

|'''Total'''
|'''$>794.26'''
|''''''
|}

==NEEDED PARTS==
These are the parts we still need.  Perhaps you can help?

{| border="1" cellpadding="10" cellspacing="0"
|-
|'''Item'''
|'''US cost'''
|'''Notes'''
|-
|Thin sheet less than 2mm thick and at least  8cmx5cm
|?
|Beer can?
|-
|[[Phoenix_RepRap/Printed Parts|Printed Parts]]
|?
|Laser Cut, Rapid Prototyped, or Printed?
|-
|Misc - oil, box cutter blades, more?
|?
|Lowes, Home Depot
|-
|'''Total'''
|'''?'''
|-
|}

==Build Log==
Sorting parts into 'kits' (whole lotta parts to sort)
Soldering - 2 or 3 stations probably (12 boards of various complexity)
*Dip soldering and SMD soldering
*Toaster oven reflow
Testing
Wiring
*ribbon data
*power
Mechanical construction
*Extruder building
*X, Y and Z
*Rods cut to length

==Status==

Electrical
*Opto endstops tested and functional
*Mobo passing e testing--however z axis stepper function seems.. odd?
*2 Stepper Controllers functioning
*1 Stepper Motor - needs testing
*1 extruder motherboard processor needs heat gun desoldering and re-seating
*1 extruder motherboard status unknown-needs testing

Mechanical
*100% prototyped parts constructed
*Extruder construction complete-need to characterize thermistor
*X axis mechanical construction begun, All axes waiting on bearings
*Wiring waiting on connectors--or if time runs out straight soldering

==Insufficiencies in Rep Rap Documentation==

===Instruction issues===
*Extruder page lists 5leds, but you actualyl need 9.  (were 9 in partlist it would seem) Led1 and Led9 are actually named Power and Debug also.
*Need better documentation on Mendel modifications to build process.  We accidentally did a lot of soldering we had to desolder.
*All mechanical construction steps don't actually give you any instructions, simply parts lists and completed pictures

===Problems in Schematics===
*Motherboard schematic claims 100u for c6, should be 10u as in documentation wiki

===Missing from partslist===
*4 conductor ribbon for the extruder
*Thermistor for extruder
*2 color 2 conductor 8amp guaged wire for power
*XLR connectors --which we're not using so thats fine
*We were short a length of 10 conductor ribbon
*Extruder lists 180ohm 1206 resistor as not required... I think?  Or is it?
*Partslist doesn't list any of the mendel mobo modification parts --3v Voltage Regulator 78L33 or electrolytic cap - we don't need anyway as we went with a sparkfun 5v ftdi breakout which matches a breakout on the mobo and gives us our 3.3v and 5v both I believe

=== Unnecessary on partslist===
*30 watt resistor - 30w-5-nd (digikey)
*SPDT Slide Switch - as atx header isnt used on mobo anymore, switch doesn't actually switch anything
*atx headers
*rj45

==Making Improvements==

===What's Out There?===

*Thingiverse Combined .stl Files:  [http://www.thingiverse.com/thing:1883 http://www.thingiverse.com/thing:1883]

===New Ideas===

*Be Able To Make It's Own Circuit Boards
*Means to Recycle Plastic
*Print on a finer scale
*Increase Print Speed
*Hot Plate for Print Consistency
*Larger Print Area